Question

OS Update WinCC (TIA Portal)

Version V1.0, Entry ID: 19701610

This entry is from the Service&Support portal of Siemens AG, Sector Industry,
Industry Automation and Drive Technologies. The conditions of use specified there
apply

(

www.siemens.com/nutzungsbedingungen

)

Go to the following link to download this document.

http://support.automation.siemens.com/WW/view/en/19701610

Question

How do you do an operating system update (OS update) on operator panels
with WinCC (TIA Portal)?

Answer

Follow the instructions and notes listed in this document for a detailed answer to
the above question.

Contents

OS Update WinCC (TIA Portal)
Version V1.0, Entry ID: 19701610

Operating System Update with
WinCC (TIA Portal)

When you install WinCC (TIA Portal), an Image file is installed as well for each
operator panel listed in the hardware catalog of WinCC (TIA Portal). On the

configuration PC, there is always only one Image file per operator panel. This
depends on the version of WinCC (TIA Portal) installed.
When you install a newer or older version of WinCC (TIA Portal), the Image files
available are replaced by the currently installed version of WinCC (TIA Portal).

The Image file includes the operating system and system files of the operator panel
concerned.

Note

As from WinCC V11 you no longer need an operating system update in the
different versions (for example, WinCC V11 SP1, WinCC V11 SP2, etc.). When
you transfer a project, all the currently associated system files (DLLs) are also
transferred automatically to the operator panel. The Basic Panels are the
exception here.

Below we provide you with an overview of when you must update an operating
system and how to do the update with WinCC (TIA Portal).
• If the operating system of an operator panel is not compatible with the version

of WinCC (TIA Portal) currently being used.

• If an Image file version of WinCC flexible is installed on the operator panel.

In both cases mentioned above you must update the operating system on the
operator panel before transferring the project.
Information about this is available in section 1.1 "Operating System Update
(OS Update)".

• If there is no operating system running on the operator panel, then you can

only update the operating system using the
"Reset to factory settings" function.
Information about this is available in section 1.2 "Resetting the Operator Panel
to the Factory Settings (Booting)".

• If you have questions about establishing the connection or problems with the

operating system update, please refer to chapters 2 "Additional Information"
and 3 "Problem Analysis".

Notes

Updating the operating system deletes all the data on the operator panel.

Therefore, first make a backup of the data below:
(using ProSave or Automation License Manager, for example)

• User administration (ProSave)
• Recipes

(ProSave)

• Licenses

(Automation License Manager), if you reset the operating system to the

factory settings.
Information about this is available in Entry ID:

27005215

Contents

OS Update WinCC (TIA Portal)

Version V1.0, Entry ID: 19701610

1.1

Operating System Update (OS Update)

Before making a project transfer WinCC (TIA Portal) checks the version
of the operating system installed on the operator panel connected.
If the operating system installed on the operator panel is different to the version of
WinCC (TIA Portal) being used, you get the message below. (For example, if a
WinCC flexible Image is installed on the operator panel or a Basic Panel is
concerned.)

Figure 1-1

If you confirm with the "Yes" button, the version of the operating system on the
operator panel is updated automatically and the configuration is transferred.

Notes

Before starting the operating system update, set the operator panel to Transfer
mode.

Contents

OS Update WinCC (TIA Portal)
Version V1.0, Entry ID: 19701610

1.2

Resetting the Operator Panel to the Factory Settings
(Booting)

If there is no operating system running on the operator panel, then you can only
update the operating system using the "Reset to factory settings" function. This is
the case, for example, if the following message is displayed when you start up the
operator panel: No image found. Waiting for image update…,

Another application is when you would like to reset all the settings in the Control
Panel of the operator panel to the factory settings. In this case, too, you can use
the "Reset to factory settings" function.

Notes

If you reset the operating system to the factory settings, you cannot use all the
communication connections and cables.

Information about which cable you can use for which operator panel is available
in section 2.1.2 "Resetting the Operator Panel to the Factory Settings (Booting)".

1.2.1

Operator Panel with Defective Operating System

Table 1-1

No.

Procedure

1. Back Up Licenses and Authorizations

If the operator panel no longer boots automatically, then you can no longer access
the file system. Then you cannot back up the existing recipes and licenses.

2. PG/PC: Setting the PG/PC interface

You only have to make a setting in the PG/PC interface with the "Ethernet" transfer
type.
• Open the "PG/PC interface" under

"Start > Settings > Control panel > Set PG/PC interface".

–

Select S7ONLINE under "Access point of the application".

–

Under "Interface Parameter Assignment Used" you select
"TCP/IP -> <Network Card Name>".

3. Operator panel: make transfer settings on the operator panel

No transfer settings can or need to be made on the operator panel.

4. Operator panel: power supply

Switch off the power supply for the operator panel.

5. Establish cable connection

Connect the operator panel to the PG/PC according to the transfer type selected.

Contents

OS Update WinCC (TIA Portal)

Version V1.0, Entry ID: 19701610

No.

Procedure

6. WinCC (TIA Portal): set transfer mode

You select the PG/PC interface depending on the communication connection
selected - serial, USB/PPI or Ethernet.
• In the project navigation, mark the operator panel of which the

Image file is to be updated.

• In the menu bar you select "Online > Extended download to device...".
• Make the relevant settings in the dialog displayed.

–

Ethernet:
An Ethernet address does not have to be specified. You can apply a
configured Ethernet address (Config IP).

–

Serial:
You can specify a baud rate of your choice.
Note:
For project transfer with the RS232/PPI multi-master cable you must set
the fifth DIP switch to the ZERO position (PPI/Freeport). Use the DIP
switches to set the highest baud rate on the cable.

• Click the "Load" button.

The "Load preview" window opens.

• "Load

preview"

window.

When the "Load preview" window opens, the configuration is compiled and the
system applies the transfer settings made.
Close the window with the "Cancel" button.

Note:
From now on you cannot change the transfer type.

7. WinCC (TIA Portal): reset to the factory settings

• In the "Online > HMI operator panel maintenance" menu bar you select the

"Update operating system" command.
The SIMATIC ProSave [OS Update]" dialog opens.
The path with the image of the operating system is already preset.
(You can also choose a different path for the image of the operating system).

• Enable the "Reset to factory settings" option.

The input field is displayed for the MAC address with the "Ethernet" transfer
type. In this case, you enter the operator panel's "MAC address".
Refer to section 2.3 for how to determine the MAC address.

• Click the "Update OS" button.

You will then receive a security warning.
Read the note. Acknowledge the message with "Yes" and you will be requested
to reboot the operator panel.

• Switch the operator panel on again. The Image file update starts. (This

procedure start can take quite a long time).

Note
If the "Reset to factory settings" check box is not displayed, refer to section 3.2.

8. Transfer project

After the installation has been completed, the operator panel remains in Transfer
mode.
For a subsequent project transfer, you first make the required transfer settings on
the operator panel.
For Touch operator panels, you should calibrate the screen beforehand under
"Control Panel > OP > Touch".

Contents

OS Update WinCC (TIA Portal)
Version V1.0, Entry ID: 19701610

1.2.2

Operator Panel with Intact Operating System

Below we take the example of a TP700 Comfort to show how to reset an operator
panel to the factory settings via Ethernet.

Table 1-2

No.

Procedure

1. PG/PC: back up licenses, recipes, etc.

Before resetting your operator panel to the factory settings, make sure that there are
no licenses, recipes, etc. on the operator panel.
The "Reset to factory settings" function deletes all the data on the operator panel.

Therefore, first make a backup of the data below
(using ProSave or Automation License Manager, for example).
• User administration (ProSave)
• Recipes

(ProSave)

• Licenses (Automation License Manager)

More information about this is available in Entry ID:

27005215

2. PG/PC: set the PG/PC interface

You only have to make a setting in the PG/PC interface with the
"Ethernet" transfer type.
• Open the "PG/PC interface" under

"Start > Settings > Control panel > Set PG/PC interface".

–

Select S7ONLINE under "Access point of the application".

–

Under "Interface Parameter Assignment Used" you select "TCP/IP ->
<Network Card Name>".

3. Operator panel: MAC address of the operator panel

To continue you need the MAC address of the operator panel.
Please refer to section 2.3 to determine the MAC address.

4. Operator panel: boot settings on the operator panel

• In the Control Panel of the operator panel you open the “OP" dialog and select

the "Device" tab.

• Click the "Reboot" button. Another window opens with two "boot options".

–

Reboot

–

Prepare for Reset

Leave this window open for the time being.

5. Establish cable connection

Connect the operator panel and the PG/PC using an Ethernet cable
(cross-over or patch cable).

Contents

OS Update WinCC (TIA Portal)

Version V1.0, Entry ID: 19701610

No.

Procedure

6. WinCC (TIA Portal): set transfer mode

If "Ethernet" is not preset for the transfer mode, then proceed as follows.
• In the project navigation, mark the operator panel of which the operating system

is to be updated.

• In the menu bar you select "Online > Extended download to device...".
• Make the relevant settings in the dialog displayed.

–

PG/PC interface type: Ethernet

–

PG/PC interface:

Ethernet

• Click the "Load" button.

The "Load preview" window opens.

• "Load

preview"

window.

When the "Load preview" window opens, the configuration is compiled and the
system applies the transfer settings made.
Close the window with the "Cancel" button.

Note:
From now on you cannot change the transfer type.

7. Operator panel: reset to the factory settings

• In the "Online > HMI operator panel maintenance" menu bar you select the

"Update operating system" command.
The "SIMATIC ProSave [OS Update]" dialog opens.
The path with the image of the operating system is already preset.
(You can also choose a different path for the image file).

• Enable the "Reset to factory settings" option.

An input field is displayed for the MAC address.

• Enter the operator panel's "MAC address".

Refer to section 2.3 for how to determine the MAC address.

• Click the "Update OS" button.

You will then receive a security warning.
Read the note. Acknowledge the message with "Yes" and you will be requested
to reboot the operator panel.

• On the operator panel you click the "Prepare for Reset"

(

see link

The operator panel boots automatically and is reset to the factory settings.
(This procedure start can take quite a long time).

Note
If the "Reset to factory settings" check box is not displayed, refer to section 3.2.

8. Transfer project

Contents

OS Update WinCC (TIA Portal)
Version V1.0, Entry ID: 19701610

Additional Information

2.1

Cable Connection between PC and Operator Panel

2.1.1

Operating System Update

When performing an operating system update, you can use all the communication
connections supported by your operator panel.

2.1.2

Resetting the Operator Panel to the Factory Settings (Booting)

If you reset the operating system to the factory settings, you cannot use all the
communication connections and cables.

Information on this is available in the table below.
The settings were made in ProSave version V9.0.0.0.

Table 2-1

Operator Panel

RS 232

Zero modem

cable

RS232/PPI

Multi-master

cable

USB/PPI

Multi-master

cable

PN PtP

Cross

Ethernet

6ES7

901-

1BF00-0XA0

6ES7 901-
3CB30-0XA0

6ES7 901-
3DB30-0XA0

6XV1 870-

3RH20

)

Standard
Ethernet CAT5

KP300

Basic mono PN

-- -- -- X

KTP400

Basic mono PN

-- -- -- X

KTP600

Basic DP

X -- --

KTP600

Basic PN

-- -- -- X

KTP600

Basic mono PN

-- -- -- X

KTP1000

Basic DP

X -- --

KTP1000

Basic PN

-- -- -- X

TP1500

Basic PN

-- -- -- X

OP 73

X -- --

OP 77A

X -- --

OP 77B

X -- -- -- --

TP 177A

X -- --

TP 177B

PN/DP

)

-- --

TP 177B

mono DP

)

-- --

TP 177B 4"

color PN/DP

-- -- -- X

OP 177B
PN/DP

)

-- --

Contents

OS Update WinCC (TIA Portal)

Version V1.0, Entry ID: 19701610

Operator Panel

RS 232

Zero modem

cable

RS232/PPI

Multi-master

cable

USB/PPI

Multi-master

cable

PN PtP

Cross

Ethernet

OP 177B

mono DP

)

-- --

TP 277

)

-- --

OP 277

)

-- --

KP400

Comfort

-- -- -- X

KTP400
Comfort

-- -- -- X

KP700

Comfort

-- -- -- X

TP700

Comfort

-- -- -- X

KP900

Comfort

-- -- -- X

TP900

Comfort

-- -- -- X

KP1200
Comfort

-- -- -- X

TP1200
Comfort

-- -- -- X

MP177

)

-- --

MP 277

)

-- --

MP 377

-- -- -- X

Mobile Panel
177 DP

)

-- --

Mobile Panel
177 PN

)

-- --

Mobile Panel
277

)

-- --

) For the RS232/PPI multi-master cable you set DIP switches 1 to 3 according to

the baud rate selected in ProSave.
DIP switches 4 to 8 must all be set to ZERO.

)

With this cable connection you cannot deselect the "Reset to factory settings"
option.

Contents

OS Update WinCC (TIA Portal)
Version V1.0, Entry ID: 19701610

2.2

Set the Image Path / File in ProSave

In the following case, you must change the Image path or the Image file
accordingly.

After you have set the WinCC flexible Image path for the operator panel displayed,
you must set the Image path for WinCC (TIA Portal) if you now wish to use the
same operator panel in WinCC (TIA Portal).

Notes

• The image path setting is device-related. The setting is retained for the selected

panel type after ProSave is closed.

• Beforehand,

make

sure that the correct Image path is set. This applies, in particular,

if WinCC flexible and WinCC (TIA Portal) are installed jointly on your computer.

In order to set the image path in ProSave, click the button to the right of the Image
path and browse through the folder tree to specify the folder path in which the
Image files are located.

In the folders you find the image files required for the respective operator panel.

Figure 2-1

Contents

OS Update WinCC (TIA Portal)

Version V1.0, Entry ID: 19701610

2.2.1

Image Path in WinCC (TIA Portal)

Sample Image path in WinCC (TIA Portal)

C:\Program Files\Siemens\Automation\\Portal V11\Data\Hmi\Transfer\11.0\Images
\OperatorPanel\*.img

2.2.2

Image Path in WinCC flexible 2008

Sample Image path in WinCC flexible 2008

C:\Program Files\Siemens\SIMATIC WinCC flexible\WinCC flexible
Images\Operator Panel\*.img

2.3

Determine the MAC Address

You can determine the operator panel's MAC address as follows.
• The MAC address is printed on the back of the operator panel

(for example, MAC-ADD.: 00-0E-8C-F8-6A-18).

• When you switch on the operator panel, the MAC address is displayed during

startup.

• By way of the "Control Panel" of the operator panel.

In the Control Panel you open the "OP" dialog and select the "Device" tab.
This tab contains the device-specific data like the MAC address.

Contents

OS Update WinCC (TIA Portal)
Version V1.0, Entry ID: 19701610

Problem Analysis

3.1

Disconnection with the
RS232/PPI Multi--Master- Cable

If the connection is disconnected when updating the operating system, set a lower
baud rate.

If you are using high baud rates, then you must use the RS232/PPI multi-master
cable with "E-Stand 03" (development status 03) or higher.

3.2

Check Box Not Available in ProSave

If the "Reset to factory settings" check box is not displayed, then recheck the
connection settings made (

Link

). It is possible that the operator panel does not

support the transfer type required for this option.

Refer here to Table 2-1 in section 2.1.2 "Resetting the Operator Panel to the
Factory Settings (Booting)".

3.3

Check Box Cannot be Deselected in ProSave

If you use the "USB/PPI Multi-Master Cable" transfer type, then, depending on the
system, on some operator panels it might not be possible to deselect the "Reset to
factory settings" option.
In this case, you cannot make an operating system update (OS Update) using the
cable, but can only do a "Reset to factory settings" (reboot).

Refer here to Table 2-1 in section 2.1.2

3 2BProblem Analysis

OS Update WinCC (TIA Portal)
Version V1.0, Entry ID: 19701610

3.4

Error Message during the Transfer of the Configuration

You have changed the operating system of your operator panel and during transfer
of the configuration you receive the message that the operating system version of
the operator panel does not match the software version used.

In this case, prior to updating the operating system, check that the Image path has
been set correctly and that you have selected the correct Image file. See section
2.2 "Set the Image Path / File in ProSave" for this.

Sample error message in WinCC (TIA Portal).

Figure 3-1

3.5

Comfort Panel "Reset to factory settings"

If a Comfort Panel is to be reset to the factory settings, then in ProSave you get
this prompt: "Please boot the operator panel...".
In this case, for Comfort Panels you must select the "Prepare for Reset" function
prior to booting, which starts updating of the operating system when the Comfort
Panel is restarted.

In this case refer to Entry ID: 60114889.

3.6

MP 377 "Reset to Factory Settings" (Booting)

If the MP 377 operator panel cannot be reset to the factory settings, then check the
Image version of the MP 377.

MP 377 operator panels with the Image version installed for WinCC flexible 2008
and higher (Image version as from V01.00.02.00_01.83) have the new parameter
"Prepare for Reset".

In this case refer to Entry ID:

35677293

3 2BProblem Analysis

OS Update WinCC (TIA Portal)

Version V1.0, Entry ID: 19701610

3.7

A Connection to the Operator Panel Cannot be
Established

Some points are given below, which you should check if no connection is
established between the operator panel and the configuration computer.

3.7.1

Check Transmission Type and Address on the Operator Panel

Compare the transfer settings on the operator panel with those on the configuration
computer.

Example:

Specification of configuration computer
•  Transfer via PROFIBUS
•  Panel address 10
Make sure that "Panel is the only master on the bus" is checked for the transfer
settings on the operator panel.

Figure 3-2

More information on the topic of "Transfer Settings" is available in Entry ID:

23802404

3 2BProblem Analysis

OS Update WinCC (TIA Portal)
Version V1.0, Entry ID: 19701610

3.7.2

Check Cable Connection and Connector

MPI/PROFIBUS cable

Please check the following points:
•  Cable connection between the operator panel and the configuration computer.
•  Check the cable for damage.
•  Bus connector especially the connection of the terminating resistors.

– Terminating resistors ON/OFF.

The following guideline value applies:
• Bus terminating resistor OFF:

– Bus connector with "two" cables connected.

• Bus terminating resistor ON:

– Bus connector with "one" cable connected.

More information on the topic of "Bus terminating resistor" is available in Entry ID:

187276

RS232/PPI multi-master cable

When using an "RS232/PPI multi-master cable", please note the switch settings.

More information on this topic is available in Entry ID:

16532946

Ethernet cable

Use a "crossed" Ethernet cable for the connection between a PG/PC and an
operator panel.

If you use a "patch" cable, you need a switch in addition.

Note
Operator panels with two "Ethernet interfaces" have an integrated switch.

3 2BProblem Analysis

OS Update WinCC (TIA Portal)

Version V1.0, Entry ID: 19701610

3.7.3

Check the PG/PC Interface on the Configuration Computer

In Windows XP:

– "Start > SIMATIC > SIMATIC NET > Set PG-PC interface".

and
– "Start > Settings > Control Panel > Setting the PG/PC Interface"

Check the following settings of the PG/PC interface

• When setting the interface parameters in

MPI or PROFIBUS, make sure that the node address is set to "0".

• We also recommend that you select the "PG/PC is the only master on the bus"

option.

• Check the "Transmission rate".
• Check the "Highest station address".

Figure 3-3

Document Outline