Making your GSO-based crayford focuser as smooth as it can get 

If you are still using those Chinese-made telescopes you probably know their built-in rack-n-pinion 
focusers are driving you nuts. I sometimes call these things "toy from hell." 
 
It's been a while we have been seeing some crayford focusers upgrade from GSO (Guang Sheng Optical) 
in Taiwan. These focusers aren't in the same league as Feather Touch or Moonlite. However, they still 
offer really good performance without breaking your bank. 
 
Problem with the GSO crayfords is that sometimes they do feel rough. 
 
Good news is there're ways to fix this little fella to make your scoping experience even more enjoyable.  

This tutorial here covers the dual-speed GSO-based crayford. It may not be 100% working for other 
crayfords like those made by Long Perng since the structure (ways to break them apart and put together) 
of their focuser is slightly different. Scopes that use Long Perng mechanics are Astro-Tech (66 & 80mm 
refractors), Stellarvue (Nighthawk Next Generation & SV102ED), Skywatcher (Equinox Series). You 
will have to let me know. Once I get enough request I will make another guide for that type of focusers. 
Before you start doing the work, you need a few things: 
 
1) A wrench 
2) Allen Keys 
3) Medium thick grease (Lithium or Graphite) 
4) A little bit of car polish wax, no really necessary but it's good to have 
5) Of course, a bit of patience ;-) 

STEP 1 
Here's a typical GSO-made dual-speed crayford.  
Make sure you are not mixing up with its tension and locking thumb screws. 
First, loosen up the TENSION thumb screw, or even take it off if you wish. 

 

STEP 2 

 
 

Take the focus knob (at left) first, you need an allen key to do the job.  

 

STEP 3 

 

Then pull the shaft out from the other side. After the shaft is pulled from the focuser the draw tube will 

come out very easily. 

 

STEP 4 
 
The flat surface of the draw tube is where the focus shaft is touching. Generally this surface is flat and 
smooth enough (way better than Synta's crayford for sure)  
Many people who own a scope with Synta's crayford have to use a grinding stone to flatten and smoothen 
the "flat" curvy suface of its drawtube.  
Good news is, no grinding stone is needed for GSO crayfords since it's flat surface is flat enough for 
doing a decent job. 
You still can make it smoother by using some car polish wax (cutting wax is recommended). Apply a bit 
of wax and wipe it off once it's dried. You should then feel it's very slippery. Yes, this is what you will 
want.  

 

 

STEP 5 
 
Now look at the inside of the focuser's main body, The 4 wheels (circled in red) are holding the draw tube 
in place. Apply a small amount of grease on all of them. 

 

STEP 6 

 

Now here comes the exciting part - The dual-speed knob!  

 

Again, use allen key to remove the fine focus knob first.... 

 

.... then the big knob  

 

STEP 7 

 

Here's the internal guts of the dual-speed knob. You see three steel balls sit inside the brass bracket. 

 

Here's the other side of the knob. The steel nut (which the red arrow is pointing) is very important, don't 

mess with it yet. This is one of the major reasons why some GSO crayfords are so rough or tight. 

 

STEP 8 

 

Look at the ball bearing side again. With all the GSO crayford I have broken apart and looked at they 

generally don't have enough lubricant for the ball bearing to move around, this is the second reason why 

the focuser feels rough, so......... 

 

......put some grease here!!!!!! Don't put too much. Then roll the brass bracket to make sure the grease is 

evenly applied. 

 

STEP 9 

 

The next thing to do is to loosen up the nut on the other side of the knob. Loosen it up VERY LITTLE. 

 

Be careful with this. If it's too loose the fine focus knob will not work or the brass bracket or even the 

little pin that holds the fine focus knob will come out. If too tight the knob will not turn at all. 

 

STEP 10 

 

Now put the big knob back in. If you turn the knob you will find it very "clicky" 

Don't worry, this is normal. Once you put the small knob back that clicky feel will be gone. I don't know 

why. Gravity? maybe.... 

A friend of mine told me the fine focus knob on all Feather Touch focusers is made by heavy brass and 
this is the reason why the turn is so smooth. I can't really confirm this but I think it's interesting enough 

for me to mention it here. 

 

 

STEP 11 

 

You can make a few turns on both the big and small knobs to see if they are at your liking or not. If the 

feel isn't making you too happy you may adjust the tension by turning the nut on the other side.  

You may have to make a few tries to get to the feel you want. 

Again, make sure it's neither too tight nor too loose. 

 

 

STEP 12 

 

Put the draw tube back in the focuser's body first... 

 

...then the dual-speed knob and shaft 

 

STEP 13 

 

This is a small part but don't miss it. Apply a bit of grease on that plastic tube thing (that sits belong the 

other focus knob), then put it back to the shaft.  

Doing this is to minimize as much friction as possible. 

 

 

 

STEP 14 

 

Put everything back together, and adjust the tension by turning the tension thumbscrew.  

 

 

And that's it! Keep in mind that this will NOT turn the focuser into Feather Touch but at least it will give 

these GSO-based focusers a fair chance to perform the way they should be. 

 

You may not get it right at first but once you get the idea behind this you later will have much better 

chance to get what you expect. 

 

Any questions? Feel free to 

ask me

.